1 p-0.4 07/27/04 pin name description en x switch enable a 3 - a 0 a ports b 3 - b 0 b ports gnd ground v cc power truth table (1) enx ax bx v cc function x (2) hi-z hi-z gnd disconnect l hi-z hi-z v cc disconnect h bx ax v cc connect pin confguration pin description features ? near-zero propagation delay ? 5? switches connect inputs to outputs ? high signal passing bandwidth (500 mhz) ? beyond rail-to-rail switching ? 5v i/o tolerant with 3.3v supply in off and on state ? 2.5v and 3.3v supply voltage operation ? hot insertion capable ? industrial operating temperature: -40oc to +85oc ? 2kv esd protection (human body model) ? latch-up performance >250ma per jesd17 ? packaging (pb-free & green available): C 16-pin 170-mil wide plastic tssop (l) C 16-pin 150-mil wide plastic qsop (q) C 20-contact tqfn (zh) block diagram low voltage, 5?, 4-channel 2-port nanoswitch ? notes: 1. h = high voltage level l = low voltage level hi-z = high-impedance 2. a pull-up resistor should be provided for power-up protection. description pericom semiconductors pi3ch series of switch circuits are produced using the companys advanced submicron cmos technology, achieving industry leading performance. the PI3CH401 is a low voltage, 4-channel switch designed with fast indiviual enables. the switch introduces no additional propagation delay or additional ground bounce noise. applications ? high bandwidth data switching ? hot-docking ? analog signal switching ? differential signal switching PI3CH401 notes: 1. n.c = no internal connection advance information a 0 a 1 a 2 en 0 en 1 a 3 en 2 en 3 b 0 b 1 b 2 b 3 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 v cc en 3 a 3 b 3 en 2 a 2 b 2 n.c. n.c. en 0 a 0 b 0 en 1 a 1 b 1 gnd n.c. en 3 a 3 b 3 en 2 a 2 b 2 n.c. n.c. en 0 a 0 b 0 en 1 a 1 b 1 n.c. gnd n.c. n.c. v cc 19 18 17 16 15 14 13 12 1 20 10 11 2 3 4 5 6 7 8 9 16 pin l, q 20 contact zh
2 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information storage temperature ................................................ C65c to +150c ambient temperature with power applied ............... C40c to +85c supply voltage to ground potential ........................... C0.5v to +4.6v dc input voltage ........................................................ C0.5v to +6.0v dc output current ............................................................... .... 120ma power dissipation ............................................................... ........ 0.5w note: stresses greater than those listed under maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specifcation is not implied. exposure to absolute maximum rating conditions for extended periods may affect re - liability. maximum ratings (above which the useful life may be impaired. for user guidelines, not tested.) dc electrical characteristics, 2.5v supply (over operating range, t a = C40c to +85c, v cc = 2.5v 10%) parameters (5) description test conditions min. typ. max. units v ih input high voltage guaranteed logic high level 1.8 C v cc + 0.3 v v il inout low voltage guaranteed logic low level C0.3 C 0.8 v ik clamp diode voltage v cc = max., i in = C6ma C C0.7 C1.8 i ih input high current v cc = max., v in = v cc C C 1 a i il input low current v cc = max., v in = gnd C C 1 i ozh high impedance current 0 a, b v cc C C 1 r on switch on-resistance (3) v cc = min., v in = 0v, i on = C48ma C 4 8 ? v cc = min., v in = 2.25v, i on = -15ma C 7 14 dc electrical characteristics, 3.3v supply (over operating range, t a = C40c to +85c, v cc = 3.3v 10%) parameters description test conditions (1) min. typ. (2) max. units v ih input high voltage guaranteed logic high level 2 v v il input low voltage guaranteed logic low level C0.5 0.8 v ik clamp diode voltage v cc = min., i in = C18ma C1.3 C1.8 i ih input high current v cc = max., v in = v cc 1 a i il input low current v cc = max., v in = gnd 1 i ozh high-impedence current 0 a, b v cc 1 r on switch on-resistance (3) v cc = min.,v in = 0v, i on = C48ma or C64ma 4 6 ? v cc = min., v in = 3.6v, i on = C15ma 5 8
3 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information notes: 1. for max. or min. conditions, use appropriate value specifed under electrical characteristics for the applicable device. 2. typical values are at v cc = 3.3v, +25c ambient. notes: 1. for max. or min. conditions, use appropriate value specifed under electrical characteristics for the applicable device type. 2. typical values are at v cc = 3.3v, t a = 25c ambient and maximum loading. 3. measured by the voltage drop between a and b pin at indicated current through the switch. on-resistance is determined by the lower of the voltages on the two (a,b) pins. 4. this parameter is determined by device characterization but is not production tested. capacitance (t a = 25c f = 1 mhz) parameters (4) description test conditions typ. units c in input capacitance v in = 0v 2.1 pf c off a/b capacitance, switch off 3.1 c on a/b capacitance, switch on 6.6 power supply characteristics parameters description test conditions (1) min. typ. (2) max. units i cc quiescent power supply current v cc = 3.6v, v in = gnd or v cc 0.8 ma
4 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information notes: 1. see test circuit and waveforms. 2. this parameter is guaranteed but not tested on propagation delays. 3. the switch contributes no propagational delay other than the rc delay of the on-resistance of the switch and the load capacitance. the time constant for the switch alone is of the order of 0.25ns for 10pf load. since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. propagational delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. switching characteristics over 3.3v operating range parameters description conditions (1) com. units min. typ. max. t plh t phl propogation delay (2,3) ax to bx,bx to ax see test diagram 0.3 ns t pzh t pzl enable time enx to ax or bx see test diagram 1.5 9.0 t phz t plz disable time enx to ax or bx 1.5 9.0 switching characteristics over 2.5v operating range parameters description conditions (1) com. units min. max. t plh t phl propogation delay (2,3) ax to bx,bx to ax see test diagram 0.3 ns t pzh t pzl enable time enx to ax or bx see test diagram 1.5 15.0 t phz t plz disable time enx to ax or bx 1.5 12.0 dynamic electrical characteristics over the operating range (t a = -40o to +85o, v cc = 3.3v 10%) parameter description test condition min. typ. max. units x talk crosstalk 10 mhz -78 db o irr off-isolation 10 mhz -60 bw -3db bandwidth see test diagram 200 500 mhz
5 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information test circuit for electrical characteristics (1) notes: 1. c l = load capacitance: includes jig and probe capacitance. 2. r t = termination resistance: should be equal to z out of the pulse generator 3. all input impulses are supplied by generators having the following characteristics: prr mhz, z o = 50 ? , t r 2.5ns, t f 2.5ns. 4. the outputs are measured one at a time with one transition per measurement. test circuit for dynamic electrical characteristics r t 10pf c l v cc v in v out 200 ? 200 ? 6.0v pulse generator d.u.t ff g11 u v d 6d switch positions test switch t plz , t pzl 6.0v t phz , t pzh gnd prop delay open
6 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information switching waveforms voltage waveforms enable and disable times input t plh 2.5v 2.5v 2.5v 2.5v t phl 3.5v 1.5v output v oh v ol t plz 1.25v 1.25v 0v v oh 2.5v v dd/2 v dd/2 t phz t pzl t pzh output output v ol +0.3v v ol v oh v oh -0.3v enx v ol applications information logic inputs the logic control inputs can be driven upto 3.6v regardless of the supply voltage. for example, given a +3.3v supply, en maybe driven low to 0v and high to 3.6v. driving en rail-to-rail ? minimizes power consumption. power supply-sequencing proper power supply sequencing is recommended for all cmos devices. always apply v cc before applying signals to the input/ output or control pins. hot insertion for datacom and telecom applications that have ten or more volts passing through the backplane, a high voltage from the power supply may be seen at the device input pins during hot insertion. the pi3chxx devices have maximum limits of 6v and 120ma for 20ns. if the power is higher or applied for a longer time or repeatedly reaches the maximum limits, the devices can be damaged.
7 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information packaging mechanical: 16-pin qsop (q) .189 .197 .053 .069 .004 .010 seating plane .025 bsc .007 .010 .228 .244 1 16 .150 .157 .016 .050 x.xx x.xx denotes dimensions in millimeters 0.635 4.80 5.00 1.35 1.75 5.79 6.19 0.101 0.254 .008 .012 0.203 0.305 3.81 3.99 0.178 0.254 0.38 0.41 1.27 .008 0.203 .015 x 45 ref detail a detail a .008 0.20 min. guage plane .010 0.254 .041 1.04 ref .016 .035 0.41 0.89 0?-6? .008 .013 0.20 0.33 packaging mechanical: 20-contact tqfn (zh) 1.50 ref . 0.400.10 0.50 typ . (14x) 0.250.05 c 0.35 2.050.10 3.050.10 3.500.10 4.500.10 (s) 3.50 ref . 0.20 ref . 0.0-0.05 pin 1 pin 20 0.750.05
8 p-0.4 07/27/04 PI3CH401 low voltage, 5?, 4-channel 2-port nanoswitch ? advance information packaging mechanical: 16-pin tssop (l) .193 .201 .047 max. .002 .006 seating plane .0256 bsc .018 .030 .004 .008 .252 bsc 1 16 .169 .177 x.xx x.xx denotes controlling dimensions in millimeters 0.05 0.15 6.4 0.45 0.75 0.09 0.20 4.3 4.5 1.20 4.9 5.1 0.65 0.19 0.30 .007 .012 ordering information ordering code packaging code package description PI3CH401l l 170-mil, 16-pin tssop PI3CH401le l pb-free & green, 170-mil, 16-pin tssop PI3CH401q q 150-mil, 16-pin qsop PI3CH401qe q pb-free & green, 150-mil, 16-pin qsop PI3CH401zhe zh pb-free & green, 20-contact tqfn notes: 1. thermal characteristics can be found on the company web site at www .pericom.com/packaging/ 2. number of transistors = tbd pericom semiconductor corporation ? 1-800-435-2336 ? www.pericom.com
|
